|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1 ML2860 SPECIFICATION ver 1.0.0 Wednesday, February 20, 2002 Oki Electric Industry Co.Ltd. ML2860 DATA SHEET 16-Tone, 32-Poly Hi-Grade PCM Sound Generator LSI Version 1.0.1, Revised on Wednesday, February 20, 2002 GENERAL DESCRIPTION ML2860 is a PCM-based hi-grade sound generator LSI, develped specifically for music ringers as used in cellular/PHS phones. With an on-chip high-quality General MIDI sound set, ML2860 is capable of playing 16 tones and 32 polyphonies simultaneously. Using the on-chip three FIFOs which store musical score data, MIDI message and ADPCM audio data, a fantastic music ringer subsystem can readily be built around this chip. APPLICATION EXAMPLES Mobile phone, PHS, Fax, PDA (Note ) Please appreciate that ML2860 is not offered for musical instrument and toy applications, such as keyboards. PACKAGE SPECIFICATION 48PIN W-CSP (P -VFLGA48-6.26x5.98-0.80-W) TOP VIEW 5.98 BOTTOM VIEW 0.8 0.59 FEATURES 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) Supports GM System level 1 On-chip high-quality GM sound set 128 timbres + 48 percussions embedded 16 timbres, 32 polyphonies simultaneously (default setting is 24) 5V open drain ports with current control for vibrator, front panel light, LED x 4 3-wire serial / 8-bit parallel bus selectable FIFO embedded for CPU power reduction Power down current: 1A (typ.) Operating current: 60mA (max.) Power supply: +2.7 ~ 3.3V Operating temperature: -20 ~ +85C Internal stereo earphone amplifier & DAC 6.26 0.73 INDEX MARK 0.15 SIDE VIEW 0.450.05 0.400.0 unit: mm(typ) 2 0.080.02 ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Input Voltage 1 *1 Input Voltage 2 *1 Power Dissipation Storage Temperature Symbol VDD VIN VIN Pd TSTG Condition Ta=25C Rating -0.3 - +5.0 -0.3 - VDD+0.3 -0.3 - +5.5 320 -55 - +125 Unit V V V mW C - RECOMMENDED OPERATING RANGES Parameter Supply Voltage Supply Voltage Supply Voltage Supply Voltage Operating Temperature M aster clock frequency Symbol DVDD AVDD IOVDD IOVDD TOP fCLK Condition DGND=AGND=0V DGND=AGND=0V DGND=AGND=0V Bus Interface DGND=AGND=0V Serial Interface Rating 2.7 - 3.3 DVDD 1.65-DVDD DVDD -20 -+85 2.7- 34 Unit V V V V C MHz 1 ML2860 SPECIFICATION ver 1.0.0 Wednesday, February 20, 2002 Oki Electric Industry Co.Ltd. BLOCK DIAGRAM VDDIO[1.65-DVDD] FIFO D7-0 CS RD WR ILE IRQ IFSEL 0: BUS / 1: Serial P7-0 1.8V CPU I/F [bus I/F] GPIO MIXINL MIXINR CLK RESET TESTI PTESTIN2-1 PTESTOUT2-1 TESTO CLOCK GEN 2.7MHz - 34MHz PWM PWM A-D VIB PANEL TEST FIFO Sequencer WAVE ROM DVDD AVDD XTGND XTVDD DRVGND Sound Generator HPAMP HPOUTL HPOUTR [Stereo] MUX / VOL FIFO ADPCM AOUT MIXOUT [mono] BIAS HPSG MIXSG TYPICAL APPLICATION CIRCUIT CPU D7-0 ADR ADR WR RD Interrupt D7-0 CS ILE WR RD IRQ IFSEL TESTI MIXINL External analog L External analog R External analog monaural According to system HPOUTR HPOUTL Audio headphone HPSG + ML2860 MIXINR PTESTIN2 -1 PTESTOUT2 -1 MIXOUT SP AMP MIXSG For system control PORT5-0 PWMD + 5V PWMA PWMB PWMC Red LED Green LED Blue LED According to system VIB PANEL SOFTWARE SUPPORT (SUBJECT TO AN NON DISCLOSURE AGREEMENT) a.) Support software for Standard MIDI file format 0/1 playback. b.) Support software for MCDF (Oki original musical score format) playback. MCDF: 1) File size compression of musical score from Standard MIDI file 2) Expand function for synchronization between picture, text, LED and MIDI. 1 ML2860 SPECIFICATION ver 1.0.0 Wednesday, February 20, 2002 Oki Electric Industry Co.Ltd. DC CHARACTERISTICS [OUTLINE] IOVDD=1.65-DVDD, DVDD=AVDD=+2.7V-3.3V DGND=AGND=0V Ta=-20-+85C , , Parameter "H" Input Voltage "L" Input Voltage "H" Output Voltage "L" Output Voltage "H" Input Current "L" Input Current Operating Current Symbol VIH VIL VOH VOL IIH IIL IDDD Condition DGND=AGND=0V IOH=-100A IOL=100A VIH=VDD VIL=0V Sound generator (Ports no load) Stereo/f=1kHz Each drive 3mW AC-Load = 32 Min. VDD x 0.8 VDDx0.8 -10 - Typ 20 18 Max. VDD x 0.2 VDDx0.2 10 30 10 20 100 150 Unit V V V V A A mA mA A A A A Standby Current IDDS Ta=-20-+40C Ta=+40-+50C Ta=+50-+75C Ta=+75-+85C 1 - AC CHARACTERISTICS / TIMING CHART [OUTLINE] IOVDD=1.65V- DVDD, DVDD=+2.7V-3.3V DGND=AGND=0V Ta=-20-+85C , , BUS WRITE TIMING Parameter ILE valid to Write Enable Low ILE valid to Write Enable High CSB valid to Write Enable Low Write Enable Pulse Width Data Valid to Write Enable Low Data Valid to Write Enable High Chip Select to End of Write Symbol tIWL tIWH tCWL tWW tDWL tDWH tCEW Min 10 10 5 25 50 0 50 Max. Unit ns ns ns ns ns ns ns D7-0 INDEX CS WR tCWL tDWL tDWH tIWL tWW tCEW tIWH tCWL tDWL tDWH tIWL tWW tCEW tIWH INDEX DATA BUS READ TIMING Parameter ILE valid to Read Enable Low ILE valid to Read Enable High Read Enable Low to Data Valid Chip Enable Low to Data Valid Read Enable High to Data Transition Chip Enable High to Data Transition Symbol TIRL TIRH TRLDV TCLDV TRHDT TCHDT Min 10 10 Max. 85 85 85 85 Unit ns ns ns tCLDV D7 -0 INDEX CS tCHDT VALID VOH VOL ns ns ns RD tIRL tRLDV tRHDT tIRH 1 ML2860 SPECIFICATION ver 1.0.0 Wednesday, February 20, 2002 Oki Electric Industry Co.Ltd. SERIAL INTERFACE DVDD =IOVDD =+2.7V-3.3V DGND=AGND=0V Ta=-20-+85C , , Parameter Chip Select Low to SCLK Low 1 Chip Select Low to SCLK Low 2 Chip Select Low to SCLK High 1 Chip Select Low to SCLK High 2 SCLK High Pulse Width SCLK Low Pulse Width SCLK Cycle Time Input Data Valid to SCLK Low1 Input Data Valid to SCLK Low2 Input Data Valid to SCLK High1 Input Data Valid to SCLK High2 Chip Select High to SCLK Low 1 Chip Select High to SCLK High 2 Chip Select High Pulse Width Output Data Valid to SCLK Low 1 Output Data Valid to SCLK High 2 Chip Enable High to Data Transition RST High to Chip Select Low RST Pulse Width Initialize Time Symbol tCLSL1 tCLSL2 tCLSH1 tCLSH2 tSH tSL tSC tIDSL1 tIDSL2 tIDSH1 tIDSH2 tCHSL1 tCHSH2 tCH tODSL1 tODSH2 tCHDT tRSC tRST tINIT Min 50 25 50 25 25 25 50 15 15 15 15 0 0 25 90 1 Max. 20 20 20 40 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ms DATA Write Timing CS(I) SCLK(I) MODE0 tSH tSL 1 2 3 15 16 Data Read Timing CS(I) SCLK(I) MODE0 tSH tSL tCHSH1 2 8 9 10 11 16 1 2 8 9 10 11 16 tCLSH1 tCLSL1 tSC tCLSL1 tCLSH1 tSC 1 2 3 15 tCH tCHSL1 16 tCH 1 SCLK(I) MODE 2 tSL tSH SCLK(I) MODE2 tSL tSH tCLSH2 tCLSL2 tSC tCLSH2 tCLSL2 tSC tCHSH2 tCH2 tCHSH2 tCH SDIN(I) tIDSL1 tIDSH1 SDIN(I) tIDSH1 tIDSL1 tCHDT SDOUT (O ) tODSL tODSL FREQUENTLY ASKED QUESTIONS Q1. What kind of musical score formats does the ML2860 support? A1. ML2860 can play Standard MIDI files under given conditions and the Oki original musical score format directly. If Standard MIDI file format 1/0 or Karaoke function need to be supported, Oki provides sample software based on NDA for this purpose. Q2. What is the condition for playing Standard MIDI file directly? A2. (1) Play format 0 only, do not play format 1. (2) Eliminate text and MIDI events not supported by the ML2860. Q3. Which MIDI events does the ML2860 support? A3. Note On/Off / Program change / Pitch bend / Channel pressure Control change [Modulation / Volume / Pan / Expression / Sustain / Reset all controller / All note off] RPN [Pitch bend sensitivity / Fine tuning / Coarse tuning] Q4. Does the ML2860 support synchronization of LED with ADPCM playback ? A4. Yes. LED and ADPCM functions are included in the musical score and are assigned as percussion to MIDI channel 10. It is necessary to build a software routine for this synchronization. |
Price & Availability of ML2860 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |